Reasons Your Fiat 500 Key Fob Won't Work
A fiat 500 key fob is a convenient way to unlock the doors and get started the car. There are a myriad of reasons the fob could stop working. This could be due to a dead coin-battery, water damage, issues with the receiver module, and interference.
This listing is for a NEW replacement Fiat Flip Key Remote that appears similar to the Ilco brand. It must be professionally programmed (click here to search for local locksmiths for your vehicle). It comes with lock, unlock and trunk buttons.
Dead Coin Battery
The most common reason your 500 key fob doesn't function is due to an inactive battery. Modern key fobs have a limited operating range, and should be within some feet of the car to operate. If you're far away from your vehicle and you press the key fob button, the car won't respond and will display a "Key Fob Not Detected" message in the instrument cluster.
If this happens, simply replace the battery of your coin cell (Part number CR2032) with a new one from a reliable brand like Panasonic, Duracell, or Energizer. You can typically find them at your local hardware store, or online.
You can test the coin-cell battery by pressing the buttons while standing close to your Fiat 500. The car will blink its parking lights, and the key fob will operate the lock and unlock switches.
If your key fob doesn't work even after replacing the battery, there may be water damage which is preventing it from communicating with the module inside your vehicle. Water damage can happen through a variety of methods, including simply splashing or submerging the key fob saltwater at the beach. If you think your fob was exposed to water, place it in a rice bag to draw out the moisture. If this doesn't work, the fob might require reprogramming by an experienced auto locksmith or by the dealer.
Water Damage
Water damage can happen if you immerse the fob in the ocean or wash it in a washer. Saltwater can cause the circuit board to short and eventually fail. It's not good to let the fob get wet however, don't give it up when you accidentally drop it in water, or fail to take it out of your pocket.
First, remove the battery from the fob. Clean the electronic chip with isopropyl ethanol or a similar product and dry it thoroughly before replacing the battery. Then try the fob and test if it works. If the key doesn't work, it might need to be reset. This is usually handled by a dealer or professional auto locksmith.
If visit this web-site is a bit older and is not programmed to work with your vehicle, you will need to replace it completely. This is a simple process which can be accomplished by a professional automotive locksmith. The locksmith will require the key to be cut to match the car's ignition. The locksmith will also have to reprogram your fob into the vehicle's system. This is a quick and affordable process which can be completed on the same day.
Receiver Module Issues
One of the most common reasons your 500 key fob could stop working is because it's out of range. The remote typically has an area of 30 feet or less, and if it's too far from your car, it won't respond to your commands. It's easy to fix this by moving the remote closer to your vehicle until it responds.
If your fob does not work after replacing the battery inside the coin, which is also called a "button", "watch" or "button" It could be a problem with the internal circuit board. In most cases, reprogramming the fob will resolve this problem. You can find the instructions for the majority of vehicles on YouTube or in the owner's manual.
It is possible to replace the metal retaining clips that hold the coin battery in place. If they become loose, it may prevent your battery from being properly seated, causing your remote to malfunction.
In rare instances, the fob can become out of connection with your vehicle as a result of hardware or software issues. You can fix this issue by visiting your local dealer or auto-locksmith to reprogram your key fob. In some instances the software may need to be reinstalled in your body control modules.
Interference
Interference can also cause the key fob to not be able to receive or transmit the signal. This could occur if the keyfob's location is in close proximity to a radio transmitter like a cell phone or radar detector. The key fob might not work due to a bad connection with the buttons water damage or damage to the internal chips.
If your key fob suddenly stopped working, or if you've tried everything at home to resolve it (e.g. replacing the battery, reprogramming it and using the spare key fob, you may have a damaged receiver module on your 500. The receiver module is located under the dash and picks up the radio frequency signals from the key fob. It converts the signals into electronic commands which are then read by the vehicle.
There's a quick and easy way to reset the 500's onboard system including the keyfob. Disconnect the battery for 15 minutes by removing first the negative cable and then the positive cable. Then reconnect the battery. This will remove any remaining electrical charge, and then restart the computer of your car. This could help you get your key fob to work again. If the problem persists you should seek out an expert technician. They can identify the root cause of your issue.